ISSN (print) 1995-2732
ISSN (online) 2412-9003

 

download PDF

DOI: 10.18503/1995-2732-2021-19-3-68-74

Abstract

Problem Statement (Relevance). From year to year, the share of additive technologies in production keeps increasing. The highest rate of growth is attributed to the use of wire and arc additive manufacturing for 3D printing as the most feasible and efficient technology. However, the available scientific and practical data are insufficient for its successful use in manufacturing parts operating at low temperatures. In this regard, it is required to carry out a more detailed study of materials produced by 3D printing and intended for operation in the Far North and the Arctic. Equipment and Methods Applied. The specimens from steel grade 07Kh25N13 were produced on the developed stand, implementing wire and arc additive manufacturing for 3D printing; the Charpy impact test method was applied, fractographs were analyzed using a scanning electron microscope. Originality. The authors determined fracture mechanisms at low temperatures applied for the specimens from steel grade 07Kh25N13 made by wire and arc additive manufacturing for 3D printing. The results obtained allow us to understand the behavior of materials and printed objects at low temperatures, which has not received enough attention previously. The authors revealed the relationship between the fractal dimension of the specimen fractures and impact toughness to estimate the effect of temperature on fracture. Result. The studies on the specimens from steel grade 07Kh25N13 showed that the fractures occurred after impact testing had four characteristic zones: crack initiation; propagation of cracks, tightening, and a break zone. A total temperature range under study showed a ductile fracture mechanism; however, with a decrease in test temperature, there is a decrease in plasticity and a decrease in the number of observed zones. The paper describes the relationship between a decrease in the fractal dimension of fracture images and a decrease in impact toughness. Practical Relevance. The results contribute to a more detailed understanding of the fracture mechanisms of the specimens from steel grade 07Kh25N13 produced by wire and arc additive manufacturing for 3D printing and assessment of the behavior of this material at low temperatures. The established relationship between the fractal dimension of the fracture and impact toughness allows us to more clearly establish the temperature reasons for the destruction of structures.

Keywords

Structural steels, 3D printing, wire and arc additive manufacturing, fractographic analysis, fractal dimension, cold resistance.

For citation

Anosov M.S., Kabaldin Yu.G., Kolchin P.V., Shatagin D.A., Chegurov M.K. Electron Microscopy Studies on the Fracture Mechanisms of Structural Steels Fabricated by 3D Printing. Vestnik Magnitogorskogo Gosudarstvennogo Tekhnicheskogo Universiteta im. G.I. Nosova [Vestnik of Nosov Magnitogorsk State Technical University]. 2021, vol. 19, no. 3, pp. 68–74. https://doi.org/10.18503/1995-2732-2021-19-3-68-74

Maxim S. Anosov – PhD (Eng.), Associate Professor, Alekseev Nizhny Novgorod State Technical University, Nizhny Novgorod, Russia. Email: This email address is being protected from spambots. You need JavaScript enabled to view it.. ORCID 0000-0001-8150-9332

Yuri G. Kabaldin – DrSc (Eng.), Professor, Alekseev Nizhny Novgorod State Technical University, Nizhny Novgorod, Russia. Email: This email address is being protected from spambots. You need JavaScript enabled to view it.. ORCID 0000-0003-4300-6659

Pavel V. Kolchin – postgraduate student, Alekseev Nizhny Novgorod State Technical University, Nizhny Novgorod, Russia. Email: This email address is being protected from spambots. You need JavaScript enabled to view it.. ORCID 0000-0002-2875-7377

Dmitry A. Shatagin – PhD (Eng.), Associate Professor, Alekseev Nizhny Novgorod State Technical University, Nizhny Novgorod, Russia. Email: This email address is being protected from spambots. You need JavaScript enabled to view it.. ORCID 0000-0003-1293-4487

Mikhail K. Chegurov – PhD (Eng.), Associate Professor, Alekseev Nizhny Novgorod State Technical University, Nizhny Novgorod, Russia. Email: This email address is being protected from spambots. You need JavaScript enabled to view it.. ORCID 0000-0001-5408-1887

1. Oliveira J.P., Rodrigues Tiago, Duarte Valdemar, Miranda R.M., Santos Telmo. Current status and perspectives on wire and arc additive manufacturing (WAAM). Materials. 2019. 12(7):1121. doi: 10.3390/ma12071121

2. Elistratova A.A., Korshakevich I.S. 3D printing technologies: advantages and disadvantages. Aktualnye problemy aviatsii i kosmonavtiki [Currently Important Issues of Aviation and Cosmonautics], 2015, vol. 1, pp. 557–559. (In Russ.)

3. Mendagaliyev R., Turichin G.A., Klimova-Korsmik O.G., Zotov O.G., Eremeev A.D. Microstructure and mechanical properties of laser metal deposited cold-resistant steel for Arctic application. Procedia Manufacturing, 2019, vol. 36, pp. 249–255. ISSN 2351-9789. doi: 10.1016/j.promfg.2019.08.032

4. Kazantseva N.V., Ezhov I.V., Davydov D.I., Merkushev A.G. Analysis of the structure and mechanical properties of the Co–Cr–Mo alloy obtained by 3D printing. Fizika metallov i metallovedenie [Physics of Metals and Metal Science], 2019, 120 (12), pp. 1271–1278. doi:10.1134/ S0015323019120088

5. Balashov A.V., Cherdantsev A.O., Novikovskiy E.A., Ananin S.V., Beloplotov S.V. Study on strength of the products manufactured by 3D printing. Polzunovskiy vestnik [Polzunovskiy Bulletin], 2016, no. 2, pp. 61–64. (In Russ.)

6. Smirnova E.A., German M.A., Fisenkova D.V. Structure and properties of samples from titanium alloy TI-6AL-4V, fabricated by 3D technology of direct metal deposition. Gagarinskie chteniya – 2019. Sbornik tezisov dokladov XIV Mezhdunarodnoy molodezhnoy nauchnoy konferentsii [Gagarin Readings – 2019. Book of abstracts of the 14th International Youth Scientific Conference]. Moscow Aviation Institute (National Research University), 2019, 924 p. (In Russ.)

7. Xu X., Ganguly S., Ding J., Guo S., Williams S., Martina F. Microstructural evolution and mechanical properties of maraging steel produced by wire+arc additive manufacture process. Mater. Charact. 2017, 143, pp. 152–162. doi:10.1016/j.matchar. 2017.12.002.

8. Kabaldin Yu.G., Kolchin P.V., Shatagin D.A., Kiselev A.V. Sposob 3D pechati na oborudovanii s ChPU s intellektualnoy optimizatsiey rezhimov [Method of 3D printing on CNC equipment with intelligent optimization of modes]. Patent RF, no. 2696121, 2019.

9. Guiding Document RD 153-34.1-003-01. Welding, heat treatment and control of pipe systems of boilers and pipelines during the installation and repair of a power plant (PTM-1c). Introduced on 02.07.2001. Moscow, 2002, 465 p.

10. Kabaldin Yu.G., Anosov M.S., Zinoviev Yu.A. Study on cold resistance of materials for critical components of facilities operating at low temperatures. Mashinostroenie: setevoy elektronnyy nauchnyy zhurnal [Mechanical Engineering: Network Electronic Scientific Journal], 2016, vol. 4, no. 2, pp. 14–17. (In Russ.)

11. Savenkov G.G., Barakhtin B.K. Relationship between the fractal dimension of the fracture surface and a set of standard tensile characteristics of the material. Prikladnaya mekhanika i tekhnicheskaya fizika [Applied Mechanics and Technical Physics], 2011, vol. 52, no. 6, pp. 177–184. (In Russ.)

12. Kabaldin Y.G., Anosov M.S., Shatagin D.A. Evaluation of the mechanism of the destruction of metals based on approaches of artificial intelligence and fractal analysis. IOP Conf. Series: Materials Science and Engineering. 709 (2020) 033076 IOP Publishing. doi: 10.1088/1757-899X/709/3/033076.