ISSN (print) 1995-2732
ISSN (online) 2412-9003

 

download PDF

DOI: 10.18503/1995-2732-2021-19-2-90-97

Abstract

Problem statement. At present, considerable attention is paid to the issues of energy saving due to limited natural resources and the increasing technology-related pollution of the environment. Absorption refrigerators differ from other cooling machines by the possibility of using secondary heat resources, such as discharges from thermal power plants, thermal waste from industrial enterprises. They are widely used in air conditioning and heating systems because of their energy-saving features, high reliability and quiet working conditions. In the design of these machines, in order to increase the efficiency of their operation, reduce the metal consumption and sizes, internally ribbed tubes are used. The production of internally ribbed tubes is possible by cutting, rolling the ribbing and rolling strips with such ribbing followed by forming into a tube. The most effective method for the production of internally ribbed tubes is a method of using rolling of ribbed strips with subsequent forming, which is characterized by high productivity and quality of the finished tubes. This study was aimed at assessing the equipment composition of the main line of quarto mill 55260220, its bearing capacity, the selection of a reasonable layout of the main line of the mill for rolling strips with the one-side ribbing. Methods used. To find the values of the torque from the technological load in rolling strips with the ribbing included in the differential equations, the simulation of this rolling process was performed using a FE model. The designed model makes it possible to determine the forces and torque of rolling taking into account tension of the ends of the rolled strip for various types of the applied ribbing. Dynamic loads on the links of the main line of the mill were determined for both layouts by compiling a dynamic model and solving the corresponding system of differential equations. Results. The authors obtained the following values: dynamic load factors acting on the links of the main drive, safety factors for stresses in the volume of the spindle devices under cyclic loads, and safety factors for torque on the motor coupling. Practical relevance. The analysis of the loading on the elements of the main line of quarto mill 55260220 made it possible to assess the equipment from the point of view of rolling ribbed strips intended for the production of internally ribbed tubes and to substantiate the rationality of the choice of the main line components for the rolling mill driven through back-up rolls.

Keywords

Absorption refrigerators, ribbed tubes, main line of the rolling mill, strip rolling, FE simulation, equipment loading dynamics.

For citation

Nekrasov I.I., Fedulov A.A., Parshin V.S. Choosing the Components of the Rolling Mill Main Line for the Ribbed Tube Production. Vestnik Magnitogorskogo Gosudarstvennogo Tekhnicheskogo Universiteta im. G.I. Nosova [Vestnik of Nosov Magnitogorsk State Technical University]. 2021, vol. 19, no. 2, pp. 90–97. https://doi.org/10.18503/1995-2732-2021-19-2-90-97

Igor I. Nekrasov – Associate Professor, PhD (Eng.), Ural Federal University, Russia. Email: This email address is being protected from spambots. You need JavaScript enabled to view it.

Artem A. Fedulov – Associate Professor, PhD (Eng.), Ural Federal University, Russia. Email: This email address is being protected from spambots. You need JavaScript enabled to view it.

Vladimir S. Parshin – Professor, DrSc (Eng.), Ural Federal University, Russia

1. Kutepov A.M., Sterman L.S., Styushin N.G. Gidrodinamika i teploobmen pri paroobrazovanii: uchebnoe posobie dlya vtuzov [Hydrodynamics and heat exchange during steam formation: a teaching aid for higher technical education institutions]. Moscow: Higher school, 1986, 448 p. (In Russ.)

2. Olimpiev V.V., Mirzoev B.G., Popov I.A. et al. Increasing efficiency of heat exchange tubes of power facilities. Inzhenerno-fizicheskiy zhurnal [(Journal of Engineering Physics and Thermophysics], 2019, vol. 92, no. 3, pp. 608–618. (In Russ.)

3. Burtsev S.A., Vinogradov Yu.A., Kisilev N.A., Strongin M.M. Choosing feasible heat exchange intensifiers in heat exchange equipment. Nauka i obrazovanie: nauchnoe izdanie [Science and education: scientific publication], 2016, no. 12, pp. 35–56. (In Russ.)

4. Mirmov N.I., Mirmov I.N. Absorption refrigerators used to generate negative cooling temperatures. Trudy BGTU [Proceedings of BSTU], 2017, series 1, no. 2, pp. 328–341. (In Russ.)

5. Skrypnik A.N., Shchelchkov A.V., Popov I.A. et al. Thermohydraulic efficiency of tubes with internal spiral finning. Journal of Engineering Physics and Thermophysics, 2018, vol. 91, no. 1, pp. 52–63.

6. Promthaisong Pitak, Boonloi Fmnart, Jedsadaratanachai Withada. Numerical investigation on turbulent forced convection and heat transfer characteristic in spirally semicircle-grove tube. International Journal of Mechanical and Materials Engineering, 2016, vol. 11, no. 1, pp. 9–11.

7. Parshin V.S., Nekrasov I.I., Karamyshev A.P., Gazman S.M. Developing the technology and equipment to produce internally ribbed tubes. Stal [Steel], 1994, no. 4, pp. 51–53. (In Russ.)

8. Kozhevnikov S.N. Dinamika mashin s uprugimi zvenyami [Dynamics of machines with elastic linkage]. Kiev: Publishing House of the Academy of Sciences of the Ukrainian Soviet Socialist Republic. 1960, 160 p. (In Russ.)

9. Ivanchenko F.K., Polukhin P.I., Tylkin M.A., Polukhin V.P. Dinamika i prochnost prokatnogo oborudovaniya [Dynamics and strength of rolling equipment]. Moscow: Metallurgy, 1970, 487 p. (In Russ.)

10. Parshin V.S., Karamyshev A.P., Nekrasov I.I., Pugin A.A., Fedulov A.A. Prakticheskoe rukovodstvo k programmnomu kompleksu DEFORM: uchebnoe posobie [Practical guide on DEFORM: a teaching aid]. Yekaterinburg, Publishing House of Ural Federal University, 2010, 266 p. (In Russ.)

11. Sotov A.V., Smelov V.G., Agapovichev A.V., Kartashov R.D. Modelirovanie protsessov OMD v programmnom komplekse Deform: metodicheskie ukazaniya [Simulation of metal forming processes using Deform: methodology instructions]. Samara: Publishing House of Samara University, 2017, 47 p. (In Russ.)

12. Dunaev P.F., Lelikov O.P. Konstruirovanie uzlov i detaley mashin [Design of machine assemblies and parts]. Moscow: Academy Publishing Center, 2008, 496 p. (In Russ.)

13. Plotnikov P.N., Nedoshivina T.A. Detali mashin: raschet i konstruirovanie: uchebnoe posobie [Calculation and design of machine parts:a teaching aid]. Yekaterinburg: Publishing House of Ural University, 2016, 236 p. (In Russ.)

14. Parshin S.V., Fedulov A.A., Karamyshev A.P., Nekrasov I.I., Pugin A.I . Oporny uzel rabochikh valkov prokatnoy kleti KVARTO [Mounting assembly of work rolls of the QUARTO mill stand]. Patent RF, no. 2497615, 2013.